Metalwork

SMH Joist Hanger Type S (SJH)

The standard hanger is designed for building into brickwork or blockwork.

SMH Joist Hanger Type R (RJH)

The return type hanger is designed for similar application to the Type S but with the advantage of a return flange (25mm as standard ) which greatly increases lateral support by giving the top flange additional resistance to pull out. We would recommend the use of TYPE R return flange hangers wherever possible for all timber to brick applications. As standard the return hanger is manufactured to suit 100mm blockwork, however any length of top flange is available to order.

SMH Joist Hanger Type D (STJH)

The straddle type joist hanger is used when timber joist positions are directly opposite each other on either side of a wall or beam. As standard the straddle hanger is manufactured to suit 100mm blockwork, however any width is available to order.

H Horizontal (Heavy Duty) Restraint Straps (HDMH)

V Vertical (Light Duty) Restraint Straps (LDMH)

Light duty restraint straps can be used for vertical restraint applications, such as holding down wall plates to masonry. These multi-holed straps are supplied in 100mm increments with 6mm holes at 25mm offset centres. Available straight, bent or twisted or in combinations as required in galvanised or stainless steel.

A190 Light Duty Hanger (Short Leg) (V81-SL)

A270 Light Duty Hanger (Standard Leg) (V81)

B340 Medium Duty Hanger (Standard Leg)

A medium duty hanger that is suitable for joist depths of up to 250mm.

B460 Medium Duty Hanger (Long Leg) (V81-Long)

B610 Medium Duty Hanger (Long Leg)

Long Leg Timber to Timber Hangers.  Manufactured from 1.5mm thick pre-galvanised steel with 50mm wide legs, suitable for solid joist or I-Beam applications, either face fixed or wrapped over supporting joists.

MINI Mini Hangers (V82)

TC Truss Clips

Attaches trusses and rafters to wall plates to provide wind restraint. Avoids skew nailing damage and provides positive resistance to wind forces. Safe working load 2.38kN uplift.

MTS Mono Truss Shoe

GTS Girder Truss Shoe (V83)

GS Glide Shoe

This glide shoe is designed to allow horizontal movement at truss bearing without affecting the overall stability of the truss whilst continuing to provide resistance to lateral and uplift forces. Secures raised tie or scissor trusses to the wall plate.

NP Hand Nail Plates (V55)

MTH/240 Multi-Truss Hangers (MH)

MTH/340 Multi-Truss Hanger

For use in heavy duty applications such as multiple truss units, main trimmer joists, purlin to beam connections or similar situations where unusually heavy loads occur.

MTH/380 Multi-Truss Hanger & MTH/CF/380 concealed flange

For use in heavy duty applications such as multiple truss units, main trimmer joists, purlin to beam connections or similar situations where unusually heavy loads occur. Also available as MTH/CF/380 with face plates folded inwards for concealed fixings.

MTH/500 Multi-Truss Hanger & MTH/CF/500 concealed flange

For use in heavy duty applications such as multiple truss units, main trimmer joists, purlin to beam connections or similar situations where unusually heavy loads occur. Also available as MTH/CF/500 with faces plates folded inwards for concealed fixings

MTH/620 Multi-Truss Hanger & concealed flange

For use in heavy duty applications such as multiple truss units, main trimmer joists, purlin to beam connections or similar situations where unusually heavy loads occur. Also available as MTH/CF/620 with faces plates folded inwards for concealed fixings.

AP Angle Plate

NPAB Nail Plate Angle

A light duty 0.9mm thick perforated angle with reinforced holes.

AB & ABL Angle Brackets

AB40 Heavy Duty Angle Brackets

Suitable for timber to timber, timber to masonry and timber to steel applications. Manufactured from heavy duty 3mm thick galvanised steel, these 40mm wide brackets and plates provide a strong connection allowing for the use of bolts, nails, screws and coach screws.

FCP Flat Connector Plates

A range of pre-punched flat connectors suitable for many timber to timber, masonry or steel applications. Manufactured from 2.5mm thick galvanised steel as standard. Stainless steel also available to order.

CB Light Duty Corner Bracket

A range of multi-purpose brackets suitable for many DIY and professional fixing applications. Manufactured from pre-galvanised mild steel.

AAB Adjustable Angle Bracket

A galvanised 90 degree connector available in a range of sizes with two slots and multi-hole pattern designed for easy adjustment.

T150 & L150 Brackets

Galvanised brackets used for connecting timbers to make a ‘T’ or ‘L’ shaped joint. Available from stock in the following sizes, additional sizing options are available to order. Thickness 2mm.

BRA Light Duty Angle Braces

Light duty angle brackets suitable for many DIY and professional fixing applications. Manufactured from pre-galvanised mild steel.

CSP Corner Stretcher Plate

Corner stretcher plate for DIY and professional fixing applications. Manufactured from pre-galvanised mild steel.

CPL Corner Plate

Corner plate for DIY and professional fixing applications. Manufactured from pre-galvanised mild steel.

MP Mending Plates

Mending plates for DIY and professional fixing applications. Manufactured from pre-galvanised mild steel.

HJS Herringbone Joist Strut (V59)

Lateral support between timber floor joists. Giving superior bracing over unreliable, slow and costly timber noggins.

FA Framing Anchor (V52)

Multipurpose fixing that can be used for connecting roof timbers, joist trimmings, studding and general timber frame construction. Slotted design allows bending on site to suit all configurations. Manufactured from 1.2mm thick galvanised steel.

HDA Holding Down Angles

A heavy duty general purpose angle plate manufactured from 2.0mm thick galvanised steel to BS EN 10346:2009 +G275.

PP Pallet Plates

A multi-purpose galvanised plate manufactured from 1mm steel, used to connect timbers without the use of nails. This product must not be used to fabricate roof trusses.

SPA Sole Plate Anchor

Designed for use as anchorage of timber sole plate to concrete base, but may also be used as a frame tie for fixing timber window frames. Manufactured from 0.9mm thick galvanised steel.

SP Splice Plate

An economical on-site method of butt jointing timbers of similar section. Suitable for use when replacing rotten floor joist ends, replacement of fire damaged timbers and repairing localised structural timber damage. Manufactured from 0.9mm thick steel. Must be fixed in sets of 4 per joint, minimum timber thickness 50mm.

SPL Safeplate (PP)

MFS Multi-Fix Strapping (GFB)

SHER/ST Sheradised Square Twisted Nails (Nails)

SS/ARS Stainless Steel Annular Ring Shank Nails

Stainless steel nails to BS1202 Part1 are supplied in polybags of 100 and 250 pieces.

DSTC / SSTC Tooth Plate Connectors

For all applications to enhance bolt performance by reducing timber rotation and joint movement. Place between timbers on an M12 bolt prior to tightening.

SPW Square Plate Washers

For use with Timber Connectors above to reinforce timber on either side when tightening with bolts.

GWB Galvanised Weather Bar

Multi-purpose flat bar made from strong galvanised steel

AS Aluminium Roof Soaker

Aluminium Roof Soakers, designed to protect against weather at the point where a roof meets a vertical face, such as a wall or chimney.

FC Fishtailed Frame Cramp

Standard pattern fishtailed frame cramps complete with 50mm upstand, three fixing holes and fishtailed end. Available in 2.0mm thick galvanised steel to BS EN 10346:2009 DX51D + G275.

WBT Window Board Tie

A pre-galvanised bracket designed to attach window boards to masonry wall. Manufactured from 13 x 3mm galvanised steel to BS EN 10346:2009 + G275.

SHI Hip Iron (HIP)