Get in Touch

Bead and Mesh

Beads designed to give true corners and edges to plaster and render internally and externally for all conditions; finishing with good resistance to cracking, chipping and impact damage on corners and edges. Standard and security grade mesh products used as a key for plaster internally and render externally and can be fixed to brick / block work, timber, steel and concrete using various proprietary fixings to provide a smooth even finish where required.

Explore our range of Bead and Mesh

GPTCB Galvanised Perforated Thin Coat Bead (GPTC)
Drylining Bead.  A thin coat board bead for plaster skimming on plasterboard lined walls. Plaster depth 2/3mm. Nail holes for easy fix with drywall nails. Scalloped edge for an excellent plaster key. Internal use only.
GMMB Galvanised Mini Mesh Bead (GMM)
Drylining bead. A thin coat bead with fine mesh wings designed for one coat plastering. Plaster depth 3mm. Fix with nails or plaster dabs. Use on plasterboard lined walls or aerated blocks. Internal use only.
GCJB30 Aluminium Control Joint Bead
An aluminium bead used to control and relieve stress and movement in drywall, preventing damage by accommodating expansion and contraction of up to 7mm.
GPPTCB Galvanised Premier Perforated Thin Coat Bead Wide Wing (GPTCLW)
Drylining bead. A perforated thin coat bead (as per GPTCB) but with slightly wider wings to give a deeper plaster key. Plaster depth 2/3mm. Nail holes for easy fix with drywall nails. Scalloped edge for an excellent plaster key. Internal use only.
GEB Galvanised Plasterboard Edge Bead
Drylining bead. A bead to reinforce the edges of plasterboard which can be fixed on either with the perforated flange on the face of the board by nailing and skimmed over or with the short flange on the board face for a decorative edge finish. Internal use only.
G3ARSB Galvanised Dry Wall Stop Bead (GPS)
Drylining bead. A bead for protection of thin coat plaster at edges and reveals and for abutment of thin coat plaster against other wall finishes. Also sometimes used as an arch bead. Nail holes for easy fix with drywall nails. Rigid but light bead perforated for an excellent thin coat plaster key. Either 3mm or 6mm Stop. Internal use only.
GTCB135 Galvanised Thin Coat Angle Bead 135º
A galvanised thin coat bead designed to create accurate 135º angles for plaster skimming on plasterboard walls.
GAB Standard Galvanised Angle Bead, Mesh Wing
Plaster and render bead.  This traditional wet plaster bead provides a strong true corner or arris, with the mesh wings allowing for a good plaster key and resistance to cracking. Fixed by plaster dabs at approximately 600mm centres, push the wings into the dabs to allow for the required plaster depth, up to 13mm, then ensure the nose is set square and plumb as required. Generally for internal use only.
GJAB Galvanised Wide Angle Bead 63mm Wing (GWAB)
Plaster and render bead.  As GAB galvanised angle bead but with a wider wing to allow for more uneven corners and slightly deeper plaster, up to 20mm.
GPSB Galvanised Plaster Stop Bead (GPS)
Plaster and render bead.  Provides a straight and clean edge to wet plaster where it butts up to other materials such as door and window frames. Fixed with plaster or mortar dabs as above or can be nailed. Generally for internal use only.
GERSB Galvanised External Render Stop (Bell) Bead (GERS)
Plaster and render bead. Used where a neat drip or ‘bell-end’ lower edge is needed on external render. Fixed by mortar dabs or masonry nails. Although this is for external use we would generally recommend Stainless Steel or PVC-u for this application only using this product in sheltered or low rainfall areas.
GMB Galvanised Movement Bead
Plaster and render bead. Designed to be used to form movement joints in plaster or render where long wall runs either have movement joints in situ or where there is a need to allow for differential or thermal movement. The bead consists of two plaster stop lengths joined by a white pvc extrusion which allows for up to 4mm of movement and which is covered by a vinyl tape which is removed after plastering or rendering. Internal use only.
GARB Galvanised Architrave Bead
A range of beads produced to allow for decorative finishes - i.e. shadow lines and recesses around door and window frames etc. The bead can either be supplied as an engaging bead or abutting bead with various plaster depths available. Internal use only.
SSAB Stainless Steel Angle Bead (SAB)
External bead. The traditional render corner bead provides a strong true corner or arris, with the mesh wings allowing for a good plaster key and resistance to cracking. Fixed by mortar dabs at approximately 600mm centres, push the wings into the dabs to allow for the required render depth, up to 13mm, then ensure the nose is set square and plumb as required.
SSPSB Stainless Steel Plaster Stop (SPS)
External bead. Provides a straight and clean edge to render where it butts up to other materials such as door and window frames.
SSERSB Stainless Steel External Render (Bell) Bead (SERS)
External bead. Used where a neat drip or ‘bell-end’ lower edge is needed on external render. Fixed by mortar dabs or stainless steel nails.
SSMB Stainless Steel Movement Bead (SMB)
External bead. Designed to be used to form movement joints in plaster or render where long wall runs either have movement joints in situ or where there is a need to allow for differential or thermal movement. The bead consists of two plaster stop lengths joined by a white pvc extrusion which allows for up to 4mm of movement and which is covered by a vinyl tape which is removed after plastering or rendering.
TLPAB 23 PVC-u Angle Bead Thincoat (PAB 23)
A PVC-u equivalent to a mini mesh or perforated thin coat bead for use with plasterboard where a skim coat is required. Fixed using drywall nails or jointing filler the profile allows for a 2mm to 3mm plaster coat to provide a neat corner edge. Internal use only.
TLPAB PVC-u Angle Bead (PAB)
A PVC-u equivalent to traditional plaster and render corner beads. The wing provides a good plaster or mortar key and the bead nose lengthens through the range to allow for increasing depths of plaster or mortar. Fixed with either plaster or mortar dabs or nails these beads can be used internally or externally.
TLPARB PCV-u Arch Bead (PPS3)
A flexible bead allowing the plasterer to form a dry wall corner arch to the radius of his choice. The nose allows for 3mm of plaster skim and forms a stop for the plaster. For use internally the bead can be fixed by nailing, jointing filler or adhesive to plasterboard.
TLPSB PVC-u Plaster Stop Bead (PPS)
Used in the same way as a steel plaster stop this bead comes in four flange widths for use with either plaster or external render. Fixing by nailing or plaster/mortar dabs the bead provides a straight edge to separate plaster or mortar from other materials. Internal and external use.
TLPERS External Render Stop (Bell) Bead (PERS)
For use with external render to provide a drip feature at the bottom of the render coat. Fixed using either mortar dabs or masonry nails the bead forms a straight edge to the bottom of the render.
TLPMB PVC-u Movement Bead (PMB)
Designed to form a movement joint where needed in a long run of plastered or rendered masonry where there is a movement joint or to allow for thermal or differential movement in a long run of plaster or render. The bead consists of two plaster stop beads joined with a white extrusion allowing for approximately 4mm of movement when installed vertically. Internal and external use.
GEML Galvanised Expanded Metal Lath
A key for plaster on suspended ceilings and walls this versatile product can also be used to encase steel columns and beams to assist in fire protection. Use internally, fixed with galvanised nails, staples or tying wire.
SSEML Stainless Steel Expanded Metal Lath (SEML)
A key for render work externally or for plaster work internally where damp conditions prevail. Fix with stainless steel nails, staples or wire or alternatively proprietary polypropylene anchors to masonry or concrete.
GRL Galvanised Rib-Lath
A key for plastering and rendering rib-lath with its stiffening ribs provides a good key for deeper coatings of plaster or render. As well as being used for walls rib-lath can also be used for partitions and ceilings. Fixed through the rib section with galvanised nails or around the rib with galvanised staples or tying wire.
SSRL Stainless Steel Rib-Lath (SRL)
A key for plastering and rendering rib-lath with its stiffening ribs provides a good key for deeper coatings of plaster or render. As well as being used for walls rib-lath can also be used for partitions and ceilings. Fixed through the rib section with Stainless Steel nails or around the rib with stainless steel staples or tying wire. External use only.
SLLD Security Lath Light Duty
This light duty Security Lath is a lightweight and economical security lath suitable for internal wall security, partitions, ceilings and roofs. Each sheet weighs approximately 6kgs and can easily be handled by one person.
SLHDR Security Lath Heavy Duty Raised
This heavy duty raised Security Lath is ideal for internal or external brickwork and can act as a key for render or plaster finishes when galvanised.
SLHD Security Lath Heavy Duty
This heavy duty Security Lath is suitable for internal wall security, partitions, ceilings and roofs. The mesh has a flattened profile and weighs approximately 24kgs per sheet.
SCA Semi Circular Arch Former
A mesh former allowing the plasterer to produce a clean edged semi-circular arch opening. The arches are supplied as a pack of four pieces and are fixed to each side of the opening then plastered over. An elliptical shape can be produced by using extra bridging pieces supplied as a separate pack. Recommended for internal use only. 1 box contains enough for 1 full arch i.e. 4 pieces.

Request Quote

Successfully added {{filename}} to your quote list